projector troubleshooting

Projector Troubleshooting: 16 Common Issues and Solutions

projector troubleshooting

Presentations nowadays are used for almost anything. From powering academic classes to working as helping content for big talks, to even offering support while doing project explanations in companies – they are essential almost everywhere.  

But the only way to make presentations possible is to use projectors. Without them, no presentation would be possible.

But like any other electronic device, a projector can also fail from time to time. And when this happens, classes, work presentations, and even big talks can be put into wait. Sure enough, you’ll want to know how to fix when any projector issue presents.

Here, we’ll help you with the most common problems that you can experience with one of these devices, and we’ll give you a straight, forward solution to each. You’ll find out more of that below.

Common Projector Problems and Troubleshooting Guide

Even though projectors look like simple devices, they’re actually more complicated than TVs and even computers. And this causes issues over time. Here are a few of these issues and their solutions:

1. Overheating Projector

Overheating Projector

Electrical devices produce heat. It doesn’t matter what type of product we’re talking about; it will get hot when working if it uses electricity. And a projector is undoubtedly one of those.

Projectors not only get hot, but they can get hotter than most other electrical appliances. And sometimes, this can be less than ideal.

When this happens, we call it overheating. An overheating projector will produce a lot of heat to the point of radiating to its surroundings.

The case or cover of the projector will feel like burning, and the desk or installation will be at least warm.

But it is not the exterior of the projector that receives the damage here, but the interior. When this happens, several things inside the device can start malfunctioning.

From the motherboard to the cooling fan, the projection bulb, and others – they may start having issues when the projector is on.

This could happen due to many issues, starting from dust getting on the cooling filter, the fan not working anymore, or even just too much sun exposure.

Luckily, all of these issues have a solution. So you won’t have to worry anymore once your projector starts overheating.

How to Fix

  • The first fix is to get the projector away from direct sunlight. As you know, sun rays are hot, so they produce heat. Especially in projectors that have tons of things inside that heat up, even the smallest rays can cause overheating. So only use them when there’s no direct sun impact.
  • Clean the projector filters. Dust tends to build up in the filters of projectors, and this is where they “breathe”, so to say. When this happens, they don’t cool down automatically, so the projector heats up more than expected. To fix this, just clean the projector filters, and that’s it.
  • Replace the internal cooling fan. This is the last resort, and only if you know that the fan has stopped working. You will have to get a new fan, open the projector, and replace the old one for the new fan yourself. If you don’t want to do this yourself, you can always contact a technician.

You can take these solutions step-by-step, so you can test the least problematic (sunlight exposure) first, then go onto the hardest (malfunctioning cooling fan).

If you don’t have to change the fan, then you’ll be happy to save some bucks and some time.

2. Projector Doesn’t Turn On

Projector Doesn’t Turn On

Sometimes, it happens that a projector just doesn’t want to start. You plug everything well, the connections with the computer look good, but you can’t still make the device work.

When this happens, you can feel pretty stressed & frustrated. But don’t worry. It can always be fixed as long as you know how to do it.

How to Fix

  • Start by reconnecting everything again. Focus on the power cord and the outlet. Sometimes, a slight movement on the power cord can move the connection and separate the pins from the outlet. Still, check everything. If it is a connection issue, then you’ll fix it.
  • If you’re using a remote control, make sure it has charged batteries. Sometimes it happens that a remote is not emitting any signal because the batteries are drained out. If this happens, you just need to replace them and use the remote again.
  • If the projector has latches, make sure they are all closed. Some projectors have a latch safety system that prevents them from turning on when they are open. The projector should turn on once you lock them.
  • Reset the lamp timer. This is a feature that prevents the lamp from turning on. It happens when the function is not working correctly. You just reset the timer, and it should let the projector turn on again.
  • Another common issue is the standby mode. It will prevent the projector from turning on or off. You can fix this one by setting the mode off. It should let the projector start afterward.

If your projector doesn’t turn on after trying each one of these fixes, then you’re probably facing a burned out projector.

This happens when it overheats to the point of complete damage. You may need to replace a vital component like the motherboard or bulb, or just get a new projector.

3. Projector Turns OFF By Itself

Projector Turns OFF by Itself

When a projector doesn’t want to turn on, you can quickly try to find and fix the problem. But when the projector turns off alone, then finding the issue is a little more complicated.

This could happen due to many different things. So fixing the problem won’t be the easiest thing. Luckily, you can always follow our advice to save time.

How to Fix

  • Check that every connection is attached correctly. Power cords can get easily detached from outlets or extensions with a simple movement. Otherwise, you can always try to connect the cable to new outlets or extensions and see if it fixes.
  • Check that the fan is working correctly. When the fan is too dirty, it won’t spin normally, and may even stop working after several minutes. This will turn off the projector automatically to prevent any overheating. Clean the fan up if this happens. If the fan is not even starting, then replace it.
  • Place a hand over the projector and feel that it is not overheating. This causes projectors to turn off automatically to prevent any internal damage. Of course, this could happen due to faulty fans, dirty filters, or too much sunlight exposure. Try the overheating fixes here.

You may find the problem to this issue by merely reconnecting the device, and that’s it. For the other issues, you may want to contact a technician to solve it more easily. Whatever the reason, it almost always has a solution.

4. Projector Doesn’t Turn OFF

Projector Doesn’t Turn OFF

In contrast with the previous issue, you can also experience a projector that doesn’t want to turn off. You press the power button again and again, in both the device and the remote control, but nothing happens.

Most of the time, this is just a technical problem with the lamp assembly or a faulty power button. To fix it, you won’t have to do much.

How to Fix

  • Start by opening the device and readjusting the lamp. If it is located in a wrong position or it just doesn’t fit entirely in place, you’ll need to set it up accordingly. To do this, take a good look at the user’s manual and installation instructions. Don’t get into the device without preparation.
  • If it is not the lamp, then it could be the power button. To solve it, a replacement for the old faulty switch is necessary. You will need to get inside, get the old button out, and replace it with a new one. This is a little harder to fix and often requires qualified hands to do so.

If none of these problems fixes the issue, then you may want to take it to a technical support shop or call an expert for a diagnosis.

5. Images Don’t Display Fully

Images Don't Display Fully

When a projector doesn’t want to show the whole video, picture, or presentation on the screen, then you’re probably suffering from a resolution problem.

However, the image cutting off doesn’t necessarily mean that there’s a resolution issue. It could also be a zoom problem or even an unadjusted window on the laptop or computer. Whatever the problem may be, there is an easy fix.

How to Fix

  • The first thing to do is to adjust the resolution on the laptop or computer. Make sure it matches the resolution of the projector. Usually, you just need to lower down the resolution. This fixes it 90% of the time.
  • Another problem could be the zoom. You may have the projector zoomed in too much. For that, you need to adjust the zoom knob by lowering it down. If the image starts to adjust as you lower the zoom, then that’s the issue.
  • If none of the previous fixes get rid of the problem, then it could be an unadjusted window. This often happens when the projector is only showing a part of a computer desktop and not the entire display. You just need to move the window to what the projector is showing, and that’s it.
  • As a last resort, you can move the projector image to the sides and see whether the problem still persists. A projection on the wrong place can also cut off the image by mistake.

This problem may be frustrating, but with care and patience, you can always fix it.

6. Poor Quality

 Poor Quality

When the image coming out of the projector doesn’t look too good, there are many different things that could be happening. But of course, they all have a solution.

One of the main problems is the resolution. If your projector is working at 720p, and your laptop is working at 1080p, then you’re likely to get a poor quality projection.

Another reason could be a bad connection between devices. If the HDMI or adapter between the laptop and projector is faulty, then the image is likely not to look too good.

Lastly, it could just be that the projector doesn’t have a proper configuration of color, contrast, resolution, or even zoom.

Any wrong setting can cause the image to look awful. You can find them all, though – so don’t worry if your projector is producing an ugly-looking projection.

How to Fix

  • Start by adjusting the resolution of both the projector and the laptop. Make sure they are working at the same resolution, so there’s no configuration problem between them. This is the most common problem when the image doesn’t look well.
  • If it is a connectivity problem, then you can fix it by reconnecting everything. Also, check the cables and see that they are in pristine condition. Faulty cables can also cause quality problems in the image. If any wire is not suitable, then replace it.
  • Lastly, make sure the projector has a proper configuration. Get into its settings and see that not only it matches the other device’s settings, but that it is configured to display images correctly. A small resolution, contrast, color, or even zoom adjustment could fix this.

If none of these fixes get rid of the problem, then you may be experiencing a lousy projection bulb or a faulty lens.

To fix any of those, you will have to contact technical support or replace the parts yourself. This could be costly and time-consuming. We often recommend getting a new projector if possible.

7. Projector Displays No Image

Projector Displays No Image

Let’s say you turn on the projector, connect the computer, and start playing a video. But then, once everything looks ready to start, nothing shows on the screen.

You’ve connected everything well, the projector looks like it is working correctly, and there’s no configuration issue (that you know of). So, what could be happening?

Well, there are a few reasons. One, it is the lamp or bulb that produces the projection. Like any other lighting device, it tends to burn out over time.

This will prevent any light from getting out of the projector, which produces no image eventually.

Two, it could be a compatibility issue with the file that you want to play. If you’re playing an ultra 4K video from a USB drive and the projector seems to be unable to play it, then it is likely a compatibility problem with the kind of file.

Third, the lenses are covered, blocked, or too dirty. This is the most common issue, even though it seems like the most obvious one for people to figure out.

Another common issue that causes the image not to show is when the standby mode is on. The projector looks like it’s working, but it doesn’t produce any image. You will even hear the cooling fan doing its job, but no picture comes out.

This often happens when someone else used the projector and didn’t turn it off. The standby mode will turn on and won’t produce any image. To any of these issues, you can find a quick solution without wasting much energy.

How to Fix

  • If it is a lamp or bulb issue, then you’ll need to replace it. This could be complicated as you will have to open the projector and replace the item directly. To make it easy for you, we recommend contacting a technician. It could be a little costlier, but it is way safer and fast.
  • For compatibility issues with specific files, we recommend bringing down the quality of the file or changing the extension. This mostly happens when you’re playing from USB devices like pen drives or hard drives.
  • If the lenses are too dirty or covered, or the projection is just being blocked, then you won’t see anything on the screen. The solution here is to get the lens cover off, to clean it, or to get anything on the projection path out of the way.
  • And if it is the standby mode, you can always try to turn the projector on and off and see if it gets fixed. Otherwise, try to look for a standby mode button and turn it off. You can always reconnect the device from power, and it should fix the problem.

If none of these solutions seem to get rid of the lack of image, then it is very likely that there has been some serious damage to your projector, and it requires complete replacement. Luckily, this is very uncommon. With a technician’s help, you can still get it working.

8. Dull or Faded Image

Dull or Faded Image

Sometimes, projections don’t look as good as they should. There’s no problem with the resolution or clarity, but with the brightness.

The colors look faded, and the whites and blacks are hard to tell apart. You just can’t enjoy anything on the image this way.

When this happens, you could either be facing a projector bulb dying out and thus not producing enough brightness.

Or you’re placing the projector in a place with too much exterior light, which reduces the image quality. For either of these problems, you won’t have any trouble getting a solution.

How to Fix

  • If you’re experiencing a lousy projector lamp, the solution would be to replace it. When it is faulty, its brightness is just not enough to provide clear & colorful images. Of course, there’s no other way to get around it than to get a new lamp or bulb.
  • If the problem is a projector in a place with too much light, then you’ll have to minimize the light or place the projector somewhere else. We always recommend getting curtains to close windows in the room, or eventually turning all the lights off. This would help the projector show the ideal image.
  • In some cases, it happens that people have weird configurations on their projector or laptop. The solution would be to fix the settings and make the image easier to project.

As you see, a dull or faded image is not something difficult to amend. You just need to know why it’s happening, and that’s it.

9. Projector Distorts Colors

Projector Distorts Colors

This is one problem that many people tend to suffer from, but it seems to have no solution. It is not the image itself, but the colors of the image, which makes it impossible to see whatever you want to enjoy on the projector. This could happen due to a faulty lamp or bulb.

The projector could have a defective lamp that’s about to die. It could also be an improper display configuration. Some projector or laptop configurations do not match each other, which could cause the image to distort.

Lastly, you could be experiencing a faulty VGA cable. This happens more often than expected, especially with VGA cables that tend to be more fragile than they look like.

How to Fix

  • The first way to fix this would be to take a look at the VGA cable. Search for any dent or missing teeth in the input. Then, try using the cable in another device to see if it works. If you don’t spot any problem, then it isn’t the cable. Otherwise, you will need to replace it.
  • As for configuration problems, you will have to make sure to get into the display settings of both the laptop/source device and the projector. Make sure you have proper optimization so the image can show without problems.
  • Finally, check to see whether the lamp or bulb is working correctly. For this, you will have to remove the lamp cover or case and check the bulb directly. Look for any crack, dent, split, or any discoloration issue in the glass. If you spot any problem with the lamp, replace it.
  • Sometimes, this could be an issue due to the color wheel or the polarizing plates. In this case, you will have to call a technician for further support. Most of the time, this requires total replacement of the device.

While it seems like an easy fix, most color issues may end up taking lots of time and effort to solve. Following our previous step, you can make it happen faster.

10. Images with Shadows

Images with Shadows

This mostly happens with DLP projectors. And when it happens, it causes the whole picture to look shadowy; not faded or dull, but as if it had something directly on the projection blurring the image.

Here, it could be either the mainboard that’s not processing the images correctly, thus delivering a shadowy screen. Otherwise, it could be the mirror or lens of the projector that needs replacement.

How to Fix

  • For problems with the mirror, you can get a replacement without trouble. You may fix it by just cleaning it, but it is unlikely to be repaired this way.
  • In case you’re experiencing a mainboard issue, you will need to replace the whole projector. There’s no other way around it.

To get into either of these conclusions, you will need to be experienced with how projectors work. If you don’t know anything about them, then we recommend taking the projector to an expert once you see a shadowy image.

11. Projector Screen with Colored Edges

Projector Screen with Colored Edges

Similar to the last issue, colored edges mostly happen with LCD projectors. And this is caused directly from a faulty prism. The prism is the part that produces the projection after receiving the signal.

Sadly, most prisms are very expensive and difficult to find. And if you want to know if it really is the prism, then you’ll have to test several other things first.

How to Fix

  • If you have an LCD projector and it is emitting images with colored edges, then there’s a high chance that the prism is faulty. For that, you will need to replace it. But as lenses tend to be truly expensive, we recommend getting a new projector.

You won’t like to spend money on a repair that may be enough to buy a new projector. In that case, get a new device, and you will be much better off.

12. Images Have Lines and Dots

 Images Have Lines and Dots

When this happens, you won’t see a distorted image or faded colors. Instead, you will see weird dots and lines across the projection.

Most of the time, these dots tend to be magenta, red, or blue. And the common cause is often dust or dirt accumulated in the projector’s panel or lens.

But if you’re experiencing long and thick lines across the screen that doesn’t look like dust or dirt, then you’re looking at a faulty mainboard. Whatever the cause is, you can always get a solution.

How to Fix

  • For spots or dots in the image, you may only need to clean the lens or dust/dirt in the green panel. We recommend taking the projector apart and carefully using a dry wipe or cotton swab to get rid of any build-up of dust on top of the lens or the green panel. That should fix it.
  • If you’re experiencing dots and lines at the same time, then you’re probably looking at a faulty mainboard. In this case, there’s no other solution than replacing the whole projector.

As you can see, small dots or spots in the image are problems that are easy to fix. But if you see lines, then it is time to replace the projector.

We also advise cleaning the projector consistently (focusing on the filters) to make sure that it doesn’t get dirty or dusty. This will prevent common spots and dots from appearing in the image.

13. Projector Inputs Not Working

Projector Inputs Not Working

When none of the inputs in the projector seem to work, then you may be facing one of the most frustrating problems. This has many reasons to happen, so finding out the solution can take some time.

Among the many causes, you will find that the input you’re using is not working anymore. This could be the RCA ports, the VGA port, the HDMI, or even the USB port.

If you’re using an adapter, then it could be faulty and causing the issue as well. Sometimes it is the cables that are broken, bent, or just plain burned out. In some cases, you might be choosing the wrong option on the display setting.

As a last resort, you should check the source of the file (computer, phone, laptop, etc.) to see if that is working correctly and sending signals properly. Luckily, all these problems have a solution.

How to Fix

  • In case it is a projector port that’s faulty, you will have to test as many of them to come to a conclusion. When a port doesn’t work, check the input source on the projector, and select other ones with the same device. If you changed the input source and the image shows, then it is the input causing the problem.
  • If you’re using an adapter, that could also be the issue. Adapters and cables may even burn out or break over time. If you use another cable with the same adapter and the problem persists, then it is the adapter causing the issue. But if the adapter works with another cable, then it was the cable.
  • Sometimes, it is the wrong input choice within the projector. If you have it connected to a computer via VGA and you’re choosing HDMI, then obviously it won’t work. Changing to the right input source would be the fix here.
  • Finally, it could be the other device not working correctly. If the laptop, computer, or any other device is not sending a proper signal, then the projector won’t receive it. Fix it by reconnecting or restarting both the projector and the other device.

In the worst-case scenario, you’re facing a mainboard problem or a physical input problem. In that case, there’s no other solution than to replace the whole projector.

14. Remote Control Not Working

Remote Control Not Working

When you have a projector with remote control, you’ll want to use the device from afar every time. But sometimes, this remote control will not work.

This mostly happens when the remote control doesn’t have any battery power left. When the batteries drain out, the remote control won’t work anymore.

Another common problem is the wrong use of the remote. Some remotes have a limited range or can get their signal distorted by almost anything.

As a last resort, you may be looking at a disabled remote. When a projector is in standby mode, then it could disable the remote functions altogether.

How to Fix

  • The first way to fix this is to check that you have enough battery power. To proceed, start by replacing the batteries for new ones, or trying the batteries in another device. If the new batteries work, or the other device works well with the old ones, then it is not the batteries.
  • When the remote has its infrared signal getting blocked, make sure nothing is blocking its path to the projector. Also, check that you’re using the remote from a close-enough distance. If you’re too far, the projector won’t receive the signal.
  • The final solution would be to check that the projector is not on standby mode or any similar modes. When this happens, the remote could be disabled entirely and not work at all.

If none of these fixes gets the remote working again, then you’re likely facing a faulty remote control. You will need to replace it with a new one.

15. Loose Parts

Loose Parts

For most people, the problem with a projector is not on the image or the digital part, but on the physical area. And it usually happens when some parts are not connected, properly aligned, or fixed to the projector, which could cause issues eventually.

For example, when the cover or case of the projector gets loose, the bulb may not turn on. This would make it impossible to get a projection from the device. The same happens if any cable or wire is loosened.

A slight connectivity problem between the primary device and the projector could cause the projector to malfunction. Of course, the best way to fix a loose part is to tighten it.

How to Fix

  • Start by checking that no cover or case in the projector is loose. If you see anything open, then close it, and the problem should go away.
  • If no cover or case seems to be the problem, then check all the cables. The solution for a bad connection is to connect it well enough.

This problem is simple, so it requires simple fixes. You can get rid of loose parts in just a few minutes. Be careful; moving a VGA, HDMI, or even USB-C cable incorrectly can cause permanent damage.

16. Projector Blinking Light

Projector Blinking Light

Some projectors have informative lights that blink again and again when there’s an issue with the device. You won’t know what’s the problem until you take a good look at the light, or eventually go into the owner’s manual to see what’s happening.

Among the most common reasons for blinking lights in projectors, you’ll find overheating, standby modes, and even faulty lamps.

Sometimes it is the power light blinking; otherwise, it is the temperature light, and in some cases, it is the lamplight. You’ll have to fix the problem accordingly.

This problem is a little more complicated than previous ones, but there are still ways to fix it.

How to Fix

  • If you are seeing the power light blinking in green, it is often a sign that the projector is preparing to start. You shouldn’t worry about this unless the projector is taking too long. In that case, you may need to take the projector to a technician.
  • If it is the lamplight blinking, it could be that the bulb is soon to wear off or burn down completely. To fix this issue, you will have to replace the lamp.
  • And if you’re seeing the temperature light flashing, then you have an overheating projector. The best way to fix this is to clean the device. You can also proceed by taking it off sunlight. Doing any of these should fix the problem.

As you see, this can be more complicated than expected, but nothing out of the ordinary. Still, we recommend always going to the owner’s manual of the projector and check precisely what kind of light you’re looking at and why it is happening. This would give you the best solution.


Fixing a faulty projector won’t be an easy job. There are many things to consider and think about. But with this guide, you will get to the problem faster than you would have without any help.

After going through all of these problems, you will probably find the one that’s causing your projector to malfunction, and you’ll find the solution in no time.

But still, we always recommend taking good care of your projector as the best way to prevent any of these issues from happening. Good luck!

Leave a Comment

Your email address will not be published.